تفاصيل الدورة

Course Outline

Centrifugal Pumps

  • Pump Categories: Dynamic (Centrifugal) and Positive Displacement (Reciprocating and Rotary)
  • Centrifugal Pumps: Operation, Casings and Diffusers, Hydrostatic Pressure Tests, Impellers, Hydraulic Balancing Devices, Mechanical Seals, Minimum Flow Requirement, Performance Characteristics, Cavitation and Net positive Suction Head
  • Maintenance Recommended for Centrifugal Pumps
Vibration Analysis and Predictive Maintenance, Centrifugal Pump Mechanical Seals, Troubleshooting of Pumps, Pump Selection

  • Vibration Analysis and Predictive Maintenance
  • Centrifugal Pump Mechanical Seals, Basic Components, Seal balance, Face Pressure, Pressure-Velocity, Power Consumption, Temperature Control
  • Seal Lubrication/Leakage, Single Inside Pusher Seal, Classification of Seals by Arrangements, Classifications of Seals by Design, Materials of Construction
  • Applications, Types of Mechanical Seals, Common Failure Modes of Seals, Seal Refurbishment, Gland Plates and Piping Arrangements
  • Installation and Troubleshooting of Mechanical Seals
  • Pump Maintenance, Inspection, Overhaul, Diagnoses of Pump Troubles
  • Troubleshooting of Centrifugal Pumps
  • Water Hammer
  • Bearings
  • Used Oil Analysis
  • Pump Selection
  • Pumping System Calculations
  • Diagnostics of Pumping Systems
  • Pump Drivers
  • Workshop: Design and selection of Different Pumping Systems for the Oil and Gas Industry and the Power Generation Industry
Centrifugal and Axial Compressors
  • Compressor Polytropic Efficiency and Power Requirements
  • Compressor Volumetric Flow Rate and Volumetric Efficiency
  • Dynamic Compressors (Centrifugal and Axial)
  • Compressor Performance Measurement
  • Receivers, Compressor Control and Compressor Unloading Systems
  • Preventive Maintenance and Housekeeping
  • Dynamic Compressor Technology
  • Centrifugal and Axial Compressors
  • Simplifies Equations for Determining the Performance of Dynamic Compressors
  • Centrifugal Compressors  Components, Performance Characteristics, Balancing, Surge Prevention Systems and Testing
  • Choking and Anti-Choking Systems
  • Compressor Auxiliaries, Off-Design Performance, Stall and Surge
Vibration Analysis

Topics:

  • Monitoring Vibration
  • Performing a Vibration Analysis
  • Determination of Velocity and Displacement                                
Lubricant and Trend Analysis

Topics:

  • Principles of Lubrication Analysis
  • Trend Analysis
  • Taking Oil Samples
  • Reading Oil Analysis Report
Techniques for Extending Bearing Life

Topics:

  • Handling and Storage
  • Proper Bearing Installation
  • Maintenance
 Principles of Reverse Double Dial Alignment

Topics:

  • Introduction to Reverse Double Dial Alignment
  • Determining Misalignment
  • Correcting Misalignment
Reverse Double Dial Alignment Procedure

Topics:

  • Prealignment Measurements
  • Determining Misalignment
  • Correcting Vertical Misalignment
  • Correcting Horizontal Misalignment 
Laser Alignment

Topics:

  • Computerized Alignment
  • Laser Alignment
  • Bracket Sag
  • Correcting Vertical and Horizontal Alignment

تحديث بتاريخ 18 September, 2019
دورات يمكنك الالتحاق بها على الفور... خذ دورة عبر الإنترنت على Maintenance Engineering ابتداءً من الآن.
  • 9 دينار بحريني
    مدة الدورة التدريبية: 1 Hour
  • Motorbike Maintenance One Education
    8 دينار بحريني
    165 دينار بحريني
    مدة الدورة التدريبية: Upto 3 Hours
See all courses

هل هذه الدورة التدريبية الاختيار المناسب لك؟

لم تجد ما كنت تبحث عنه؟

أو