Laimoon.com

Car Scanner Auto EFI Electrician Mechanics - Institute of Professional and Technical Studies (IPATS) , Pakistan, Rawalpindi

Fri, 24 Jan 2020 21:09:54 +04

Auto mechanics Campus Based Course Trainings

Automotive service shop procedures
Mechanical diagnostic techniques
Gas engine & fuel systems
Brake systems
Steering, suspension and tires
Electrical and electronic systems
Vehicle service and repair
Emissions tuning
Safety and environmental procedures

Engine Service Course
A course in engine repair teaches students about the parts of an engine and their functions, as well as how to assemble and take apart the engine. Students learn about the different types of engines and how to safely maintain and repair them. Since the engine of an automobile is the most vital part of the car's performance, engine repair courses are often among the first courses taken in auto mechanic training programs.

Brake Service Course
Brake repair courses show students how to diagnose and fix problems in drum brakes and disc rotors. Students also learn about the science behind hydraulics, as well as modern anti-lock brake systems. A brake repair course is a must for any aspiring auto mechanic, which is why most schools offering auto mechanic programs require students to take a brake repair course at or near the beginning of the program.

Electric System Course
An electric systems course shows the applications of electronics in automobiles, particularly in starting the car, the car battery, the car's internal computer and the other electronic systems that monitor the car's performance. This course is usually taken after courses in engine and brake repair, but is taken early in the program since many automotive problems are due to electrical malfunctions.

Automotive Steering Course
Courses in automotive steering discuss the mechanisms that make a car travel in the driver's intended path. Suspension systems, wheel alignment and the geometry of steering are covered in most automotive steering courses. The placement of an automotive steering course in an auto mechanic training program can vary; however, the precise nature of automotive steering requires a trained eye and is therefore is generally only taught after the first half of the program is complete.

Auto Mechanics Module 1 Introduction to Auto Mechanics

The Auto Mechanics Trade Today and Tomorrow
Safety First: What You Need to Know on Day One
On Overview of Automobile Systems and Their Main Repair and Maintenance Tasks
Important Tools and Instruments
Practical Exercises
Alternative Fuels and Automotive Technologies

Auto Mechanics Module 2 Automotive Technology

Careers in the Automotive Industry
Workplace Skills
Basic Theories and Math
Automotive Systems
Hand Tools and Shop Equipment
Diagnostic Equipment and Special Tools
Working Safely In the Shop
Preventative Maintenance and Basic Services

Auto Mechanics Module 3 Engines

Automotive Engine Designs and Diagnosis
Engine Disassembly and Cleaning
Lower End Theory and Service
Upper End Theory and Service
Engine Sealing and Reassembly
Lubricating and Cooling Systems

Auto Mechanics Module 4 Electricity

Basics of Electrical Systems
General Electrical System Diagnostics and Service
Batteries: Theory, Diagnosis, and Service
Starting and Motor Systems
Charging Systems
Lighting Systems
Instrumentation and Information Displays
Basics of Electronics and Computer Systems
Electrical Accessories

Auto Mechanics Module 5 Engine Performance

Engine Performance Systems
Detailed Diagnosis and Sensors
Ignition Systems
Ignition System Diagnosis and Service
Gasoline, Diesel and Other Fuels
Fuel Delivery Systems
Electronic Fuel Injection
Fuel Injection System Diagnosis and Service
Intake and Exhaust Systems
Emission Control Systems
Emission Control Diagnosis and Service
Hybrid Vehicles
Electric Vehicles

Auto Mechanics Module 6 Manual and Automatic Transmissions and Transaxles, Suspension and Steering Systems, Brakes and Passenger Comfort

Clutches
Manual Transmission and Transaxles
Manual Transmission and Transaxle Service
Drive Axles and Differentials
Automatic Transmissions and Transaxles
Electronic Automatic Transmissions
Automatic Transmission and Transaxle Service
Four and All-Wheel Drive
Tires and Wheels
Suspension and Steering Systems
Restraint Systems
Wheel Alignment
Brake Systems
Drum and Disc Brakes
Anti-lock Brake, Traction Control, and Stability Control Systems
Heating and Air Conditioning
Heating and Air Conditioning Diagnosis and Service

Cost: 32500 PKR

Duration: 3 Months

EFI Auto Electrician - International College Of Technical Education , Pakistan, Rawalpindi

Sat, 14 Dec 2019 14:54:54 +04

EFI Auto Electrician Course :

Apply Safe Working Practices In An Automotive Workplace
Use And Maintain Automotive Electrical Test Equipment
Carry Out Soldering Of Electrical Wiring And Circuits
Demonstrate Knowledge Of Automotive Electrical Circuits And Wiring Systems
Install, Test And Repair Vehicle Lighting And Wiring Systems
Fabricate, Test And Repair Wiring Harnesses And Looms
Test And Repair Basic Electrical Circuits
Demonstrate Knowledge Of Petrol And Diesel Engine Operation
Diagnose And Repair Electronic Spark Ignition Engine Management Systems
Diagnose And Repair Electronic Compression Ignition Engine Management Systems
Test, Charge And Replace Batteries
Install Ancillary Electronic Control Unit Systems And Components
Diagnose And Repair Instruments And Warning Systems
Diagnose and repair charging systems
Diagnose And Repair Ignition Systems
Repair Electrical Systems
Service And Repair Electronic Body Management Systems
Service And Repair Electronic Drive Management Systems
Carry Out Diagnostic Procedures
Remove And Replace Supplementary Restraint Systems

Cost: 25000 PKR

Duration: Upto 3 Months

Quantity Surveying Diploma - International College Of Technical Education , Pakistan, Rawalpindi

Thu, 21 Nov 2019 09:39:13 +04

Surveyors work in a variety of different settings including people's homes, the sea bed, roads and motorways, collectables and large construction sites. They are also responsible for the protection of the environment in which they are ;A quantity surveyor (QS) is a professional working within the construction industry concerned with construction costs and contracts. Services provided by a quantity surveyor may include: Cost planning and commercial management throughout the entire life cycle of the project from inception to ;A quantity surveyor manages all costs relating to building and civil engineering projects, from the initial calculations to the final ;Surveyors seek to minimise the costs of a project and enhance value for money, while still achieving the required standards and quality.

Course Contents:

Construction technology
Business and construction economics
Construction law
Arbitration
Building technology and service
People and information management
Facilities management
Estate management
Architecture and design appraisal
Professional development
Computer-aided design
Value engineering
Feasibility studies
Planning law
Risk analysis
Estimating and valuation
Substructures and drainage
Floors and roofs
Commercial management
Conversion and refurbishment
Property development.

Cost: 25000 PKR

Duration: Upto 3 Months

Civil Surveyor and Land Surveyor (QC) - International College Of Technical Education , Pakistan, Rawalpindi

Wed, 20 Nov 2019 08:58:57 +04

Mofa attested Land Surveyor Diploma Course, World Wide Acceptable with UK/USA/Pak/ International Certifications in Rawalpindi, Islamabad, Admission open, We offers specialized and centralized fully equipped computer lab,various professional lecture rooms with multimedia for audio /video visual aid,Conference hall,hands-on supervisory experience in service and operations, Surveying or land surveying is the technique, profession, and science of determining the terrestrial or three-dimensional position of points and the distances and angles between them. A land surveying professional is called a land surveyor.

These points are usually on the surface of the Earth, and they are often used to establish land maps and boundaries for ownership, locations like building corners or the surface location of subsurface features, or other purposes required by government or Land law, such as property sales. Surveyors work with elements of geometry, trigonometry, regression analysis, physics, engineering, metrology, programming languages and the law. They use equipment like total stations, robotic total stations, GPS receivers, retro reflectors, 3D scanners, radios, handheld tablets, digital levels, drones, GIS and surveying software. Surveying has been an element in the development of the human environment since the beginning of recorded history.

The planning and execution of most forms of construction require it. It is also used in transport, communications, mapping, and the definition of legal boundaries for land ownership. It is an important tool for research in many other scientific ;The simplest method for measuring height is with an altimeter using air pressure to find height. When more precise measurements are needed, means like precise levels (also known as differential leveling) are used. When precise leveling, a series of measurements between two points are taken using an instrument and a measuring rod. Differences in height between the measurements are added and subtracted in a series to get the net difference in elevation between the two endpoints. With the Global Positioning System (GPS), elevation can be measured with satellite receivers. Usually GPS is somewhat less accurate than traditional precise leveling, but may be similar over long ;Land Surveyor Course

Content:

Introduction Land Surveyor
Classification of survey
Land Serveyor
Principles of survey
Chain survey
Plotting of chain survey
Compass survey
Bearing system
Drawing Scales
Types of scales
Leveling
Technical terms
Purpose of Leveling
Plain table survey
Methods of plane table survey
Adjustment of Levels
Total Station Practical Training
Auto Level / Theodolite Training
GPS Practical Training.

Cost: 25000 PKR

Duration: Upto 3 Months

Quality Control QC Inspector Diploma - Institute of Professional and Technical Studies (IPATS) , Pakistan, Rawalpindi

Sun, 26 May 2019 16:04:24 +04

Diploma in Quantity Surveyor Advance Course Certification Islamabad Rawalpindi)

Institute of Professional and Technical Studies (IPATS)

COURSE DETAILS

Quality Systems Training This program is designed to provide skills necessary to become a Quality Assurance or Quality Control Associate employed by manufacturing companies in a variety of business sectors. The concepts and skills presented in this two week program are relevant to both production and service applications.

Module 1

Concepts in Quality Organizational Framework Professional Practices - Ethics Quality as a concept and business practice is defined. Applicable standards and regulations for various manufacturing and service industry sectors will be introduced. Lean manufacturing and six sigma concepts and how they tie into the professional framework will also be discussed.

Module 2 Quality Systems Auditing Professional Practices - Confidentiality ISO 9001:2008, ISO 13485:2003 and FDA Current Good Manufacturing Practices are discussed in detail. Students will be introduced to and apply auditing principles as they relate to the standards. Confidentiality professional practices will be presented.

Module 3 Measurements This introduction to Applied/Industrial Metrology will cover measurement fundamentals and calibration. Students will be introduced to accuracy and precision and how they are affected by the equipment, environment, and measurement systems. There will be limited hands-on time for common physical measurement tools.

Module 4 Inspection and Sampling Print Reading In this module, measurement fundamentals discussed in Module 3 will be expanded to include inspection methods and sampling plans. Evaluating processes to determine when, where and how to take a sample will be covered. Understanding material specifications and component drawings will also be discussed.

Module 5 Analysis A general review of shop math and statistics will be covered. The student will be provided an overview of how to evaluate the data gathered via inspection to make product release decisions. Reporting the data and using Excel® in the workplace will also be discussed. Students will participate in small exercise that explores data collection and analysis.

Module 6 Quality Operations Professional Practices - Teamwork Conflict Resolution Communication Quality Control throughout industry is typically the group that determines the acceptability of both raw materials (components) used to manufacture the products and whether the product can be shipped. This module will explore how this is applied in the workplace. Teamwork, conflict resolution and communication skills will be presented and demonstrated.

Module 7 Root Cause Investigation CAPA Systems Throughout industry understanding and solving problems is a necessary skill. This module will look at commonly used tools such as the fishbone diagram, who/what/where/when/why/how and 5-whys and their use in evaluating situations, leading toward solutions. Corrective Action and Preventive Action systems are required by both ISO and FDA.

Module 8 Validation An integral part of the quality system, validation is a structured method for documenting and demonstrating that processes and products function as intended. The requirements for design, installation, operation and performance will be covered.

Module 9 Lean Six Sigma Lean manufacturing focusses on the elimination of waste, whereas Six Sigma focuses on the elimination of defects. These business philosophies will be discussed in reference to how they function within the quality system.

Course Areas :

Quality assurance
Inspection and quality control
Normative documents
Insulation systems
Insulating materials
Protective coverings
Fixings
Insulation design (basic)
Application of insulation
Scaffolding
Handling and storage of materials
Health and safety considerations
Common problems encountered
Corrosion under insulation
Reporting
Standards applicable

Diploma in Quantity Surveyor Advance Course Certification Islamabad Rawalpindi)

Institute of Professional and Technical Studies (IPATS)

Cost: 37500 PKR

Duration: 3 Months

Project Management using Primavera P6 - Institute of Professional and Technical Studies (IPATS) , Pakistan

Sun, 10 Feb 2019 19:16:40 +04

IPATS Govt Education Zone in Khanna Pul Rawalpindi offering professional educational services and trainings in this area. Now days we are trying to enhance our goals for the betterment of our young generation and to improve the quality of education in the field as it our utmost desire to educate the nation rather to teach. Mitsubishi multimedia projectorsand audio visual recording systems available to facilitate the distance learning students.

1 - Introduction to this Course and Course Objectives
2 - Introduction to Project Management Body of Knowledge (PMBOK)
3 - An overview of Project Schedule Management
4 - Fundamentals of Project Management

What is a Project?
What is Project Management?
Five Process Groups of Project Management
Schedule and its Importance
ritical Path Method for Scheduling
Understanding a Gantt chart

5 - Introduction to Primavera Systems and Oracle
Primavera P6 PPM
6- Primavera P6 Installation
7 - Primavera P6 Interface and Preferences
8 - Organizational Breakdown Structure
9 - Enterprise Project Structure
10 - Work Breakdown Structure
11 - Planning your Work Schedule
12 - Understanding a Sample Project
13 - Creating a New Project in Primavera P6
14 - Project Window Options
15 - Understanding Project Must Finish and Total Float
16 - Role of Calendars in Scheduling
17 - Understanding and Adding Calendars
18 - Project and Database Default Calendar
19 - Creating WBS in Primavera P6
20 - Understanding Percentage Complete Types
21 - Understanding Activity Types
22 - Setting Defaults for New Activities
24 - Estimating Duration of Activities
25 - Adding Duration of Activities
26 - Understanding Relationships
27 - Adding Relationships and Scheduling
28 - Understanding Scheduling Algorithm
29 - Scheduling Options
30 - Formatting Bars, Columns and Timescale
31 - Group, Sorts and Layouts
32 - Filtering in Primavera P6
33 - Printing, Exporting and Importing
34 - Reporting in Primavera P6
35- Understanding and Adding Baseline
36 - Updating a Project
37 - Assigning Baselines and Monitoring a Project
38 - Adding and Assigning New Currency
39 - Understanding Roles, Resources and Expenses
40 - Adding Resources
41 - Duration Types in Primavera P6
42 - Assigning Resources and Reviewing Resource Allocation
43 - Adding Expenses
44 - Developing Project Funding Requirements and Cost S-curve
45 - Updating a Project with Resources and Expenses

Course Topics:

Project Management Life Cycle
Understanding Data in P6
Overview and Navigation
Creating a Project
Creating a Work Breakdown Structure
Adding Activities
Calendars
Creating Relationships
Scheduling
Assigning Constraints
Customizing Activity Views
Understanding Roles and Resources
Assigning Roles and Resources
Project Workspace
Optimizing the Project Plan
Baselining the Project Plan
Methods of Applying Progress
Executing the Project Plan
Analyzing the Updated Project
Portfolios and Dashboards
App A – Updating the Project Using Timesheets
App B – Reporting

Learn To:

Create a project
Add activities
Create relationships
Assign and analyze resources
Analyze project performance
Execute and control the project
Customize dashboards and the project workspace
View reports

Course Objectives:

Create a project
Create a Work Breakdown Structure
Add Activities
Customize activity views
Create Relationships
Schedule the project
Assign constraints
View the Enterprise Project Structure
Optimize the project schedule
Assign roles and resources
Analyze resources and cost
Baseline the project plan
Execute the project
Customize dashboards
Manage risk
View reports

Learn Outcomes

Add a Project to the Project Structure
Create a Work Breakdown Structure
Add Reference Documents
Add Activities
Add Steps and Roles to Activities
Create Relationships
Schedule a Project Add Constraints Organize Activities
Assign Resources and Costs to Activities
Analyze Resource/Cost Usage Optimize the Schedule
Create and Monitor Thresholds ,Status the Project ,Analyze the Statused Project

Case Study

Calculating Percent Complete

Describe the three Percent Complete Types.
Determine which Percent Complete Type to use based on how your organization reports progress.
Explain how activity percentages are calculated based on the Percent Complete Type chosen.
Use weighted steps to calculated Percent Complete.

Earned Value

Define earned value.
Define Performance Percent Complete.
Review the results of different earned value techniques.
Recognize the benefits of using earned value analysis.

Advanced Scheduling

Calculate multiple float paths when scheduling.
Explain the difference between scheduling logic options.
Describe a calendar’s effect on lag.

User-Defined Fields and Global Change

Create a user-defined field.
Run a global change.

Managing Multiple Projects

Filter and apply progress to multiple projects.
Set the default project for multiple projects.
Explain how project elements are handled in multi-project mode.

Cost: 20000 PKR

Duration: 1 Months

Auto and Diesel Technology Diploma - Institute of Professional and Technical Studies (IPATS) , Pakistan, Rawalpindi

Wed, 09 Jan 2019 21:42:30 +04

What is an Auto and Diesel Technology Diploma?
An auto and diesel technology diploma program will imbue you with the skills and experience you need to be a successful auto mechanic. Hands-on experience is essential as you learn about different auto technologies like hydraulics, electrical systems, welding, air intake, brake repair, and engine building. A typical diploma program for auto and diesel technology will include the following courses:

Engine Fundamentals
Brakes
Electrical Systems
Heating and Air Conditioning
Engine Rebuild
Diesel Electrical Systems
Computer Literacy
Alignment/Steering/Suspension

Course Contents:

1- Explain all kind of sensors and their works? 1)Mass Airflow Sensor, 2)Manifold Absolute Pressure Sensor,
3)Air Vortex Sensor, 4)Fuel System Sensor, 5)Temperature Sensor, 6)Throttle Position Sensor,7)Exhaust Gas Oxygen Sensor, 8)Crank Angle Sensor, 9)Hall Effect Voltage Sensor

2-Identification of different types of vehicle Knowledge about automobile industryIdentification of Vehicle Identification Number, Chassis No. & Engine no, Basic automotive terms and familiarization to various types of vehicles

3-Identification of different types of engine components. Career path for the trainee in the Dealership Replace- air cleaner, oil filter & fuel filter Understanding working of 2 stroke and 4 stroke engines Apply Grease to parts / through greasing points (if necessary) Types of fuel used in vehicles, spark ignition and compression ignition engines Check power plug and inspect cables Understanding of technical terms and definitions Wheel base and track, compression ratio, Stoichiometric ratio Clean, Check and Adjust spark plug Understanding of various components viz. Battery, Spark plug, Air Filter, Fuel filter, Oil filter, Injector, Body parts, etc Ignition Timing checking on Petrol vehicle with timing light & Ignition timing adjustment Knowledge of vehicle assembly.

4- Vehicle Service Process Vehicle Service Process (Personal & Vehicle Safety procedure PDI & Periodic Maintenance Schedule of various MSIL models , Personal & Vehicle Safety procedure followed in shop floor Air Filter - Working, PDI & Periodic Maintenance Schedule of various MSIL models Fuel Filter - Working, Air Filter - Cleaning process, Replacement Period & Process, Engine Lubrication System, Fuel Filter

5- Fuel-supply system components Air intake system components Electronic control components list of cars are compactable to EFI scan (engine code with model-chassis numbers Fuel System Fundamentals : Fuel Pumps, Fuel Filters, Fuel Injection and Carburetion, Idle Speed Control, Fuel Pump Control Module, Computer-Controlled Fuel Systems, Feedback Fuel Systems, How does the Oxygen Sensor Work? Zirconia Sensors and Titania Sensors. The Electronic Control Module(ECM)

6- What is EFI? And explain the benefits of EFI? Basic Terminologies define with Scope. Electronic control components with the Electronic control components
What is Fuel Tank and Explain the Purpose of Fuel Tanks, and Components of Fuel Tank? What is Sensors and explain how the sensor works in EFI System?

7- Carburettor Fuel System for a Piston Engine, What is Electronic Control Unit? And which things depend on ECU, What is Scanner? Use of Scanner and prescribe different kinds of scanners and their advantages? How to configure the Scanner? Step-by-step installation.

8-Explained the different kind of Filters and their work? Internal and external structure of the Scanner? What is ignition and different type of sensor lights when you switch on (IGNITION), Mechanical EFI Parts? And Electrical Components.
Define the reasons which increase the temperature of Moter? Define the terms (Engine Fan, Radiator, Fan Belt, Thermostats wale , Radiator Tanks, Water Storage Tank, timing belt)

9-Petrol Engine Petrol Engine Identification of petrol Engine components. 4-stroke spark-ignition engines- Basic 4-stroke principles. - Practice on starting and stopping of petrol engines. Observe and report the reading of Tachometer, Odometer, temp and Fuel gauge under ideal and on load condition, Spark-ignition engine components- Basic engine components, Engine cams & camshaft, Engine power transfer, and Engine components.

10-Explain the difference between Carbonator system and injectors system?

Modern Vehicle Technology
Motor Vehicle Management
Vehicle Maintenance
Organizational Management
Vehicle Maintenance Lab
Project, Industrial Visit, and SeminarFoundry,
Welding and Sheet Metal Practice
Special Vehicle and Equipment-
Strength of Materials

Mechanical Engineering
Diploma in Mechanical
Diploma in Automobile
Diploma in Aerospace
Diploma in Materials
Diploma in Mechanical (Power)
Diploma in Mechanical (Production)
Diploma in Precision Mechanical & Instruments
Diploma in Auto & Diesel Tech
Diploma in Dies & Mould
Diploma in Automation
Diploma in Refrigeration & Air Conditioning
Diploma in Mechanical (Construction Machinery)

Cost: 35000 PKR

Duration: Upto 3 Months

Auto electrician,auto mechanic,automobile engineering - Institute of Professional and Technical Studies (IPATS) , Pakistan, Rawalpindi

Thu, 20 Dec 2018 21:11:37 +04

Auto electrician,auto mechanic,automobile engineering Course

Auto electrician courses prepare students to work with different types of vehicles and focus on the engine and other systems. Students taking auto electrician courses learn some basic engine management rules and principles, and participate in a number of hands-on projects to acquire the necessary skills needed for a successful car electrician career. Examples of auto electrician courses in a typical auto electrician training program include:

Basic Engine Management Systems
Drivability Diagnostics
Drivetrain Systems
Chassis
Computerized Repair System
Health, safety and good housekeeping in the automotive environment
Support for job roles in the automotive environment
Materials, fabrication, tools and measuring devices used in the automotive environment
Diagnosis and rectification of vehicle auxiliary electrical faults Inspecting vehicles using prescribed methods
Diagnosis and rectification of engine electrical faults Diagnosis and rectification of transmission and chassis
electrical faults Conducting vehicle enhancement and installation consultations with customers in the motor vehicle environment

COURSE CONTENT:
Monitor Environmental And Sustainability Best Practice In The Automotive Mechanical Industry
Apply Safe Working Practices
In An Automotive Workplace Use And Maintain Automotive Electrical Test Equipment Carry
out Soldering of Electrical Wiring And Circuits Demonstrate Knowledge of Automotive Electrical Circuits And Wiring Systems Install, Test And Repair Vehicle Lighting And Wiring Systems Fabricate, Test And Repair Wiring Harnesses And Looms Test And Repair Basic Electrical Circuits Demonstrate Knowledge of Petrol and Diesel Engine Operation Diagnose and repair Electronic Spark Ignition Engine Management Systems Diagnose And Repair Electronic Compression Ignition Engine Management Systems Test,harge And Replace Batteries Install Ancillary Electronic Control Unit Systems And Components Diagnose And Repair Instruments And Warning Systems Diagnose and repair charging systems Diagnose And Repair Ignition Systems Repair Electrical Systems Service And Repair Electronic Body Management Systems Service And Repair Electronic Drive Management Systems Carry Out Diagnostic Procedures Remove And Replace Supplementary Restraint Systems

Auto EFI Training Center in IPATS.
Diagnostics tools awareness.
Uses of diagnostics tools: Faults Finding: Faults Erasing: Meter Reversing: Awareness of OBD Codes: Awareness of Engine Codes: Awareness of Body Codes: Awareness of ABS Codes: Awareness of Airbag (SRS) Codes Digital Meter Correction/Reverse Training Key Programming Training, ALL sensors locution and fault solution

Automotive Vehicle Brakes
Vehicle Brake Inspection
Vehicle Lighting and Electric-System Inspection
Inspecting Vehicle Glazing Inspecting the Vehicle Body and Accessories

Use electrical testing instruments Conductors and cables Fault finding on basic electrical circuits Remove and mount bearings Starter motors Alternators Ignition system and lights Monitoring circuits Auxiliary circuits Maintain a storage battery ,

Electronic ignition and fuel injection Wiring harness and connectors General maintenance Diagnosis and testing of electrical systems Combined tasks Headlight adjustment ,

Installs, repairs replaces and overhauls wiring, starters, generators, distributors and other electrical equipment of motor vehicles.

Examines vehicle battery, checks voltage and specific gravity using special equipment such as voltmeter hydrometer, heavy discharge tester, etc. and ensures that battery is in good condition.
Checks vehicle wiring, locates faults and rectifies defects by replacing damaged wire or connecting ends with insulation tape. Starts engine to check whether alternator is charging correctly, and if distributor, condenser coil and cut out are functioning properly. Estimates nature of defects and reports components to be replaced or repaired.

Dismantles and repairs electrical units and components such s generator, distributor etc. where required ,

This qualification will provide you with skills and knowledge used in the automotive electrical technology sector which includes inspection, service and repair.

Inspecting the Fuel System
Inspecting the Exhaust System
Automotive Vehicle Emission Controls
Automotive Emission-Control Inspection
Special Problems in Inspection of Heavy-Duty Vehicles
Inspecting Truck and Bus Tires and Wheels
Truck and Bus Steering, Alignment, and Suspension Inspection
Heavy Motor Vehicle Brakes
Heavy Motor Vehicle Brake Inspection
Heavy Motor Vehicle Lighting and Electric-System Inspection
Inspecting Heavy-Duty Vehicle Body and Engine Systems

Cost: 35000 PKR

Duration: 3 Months

Autodesk Revit (Architecture/Structure/MEP) - Institute of Professional and Technical Studies (IPATS) , Rawalpindi,Pakistan

Mon, 03 Dec 2018 20:19:58 +04

Revit 3D Course in Rawalpindi,Revit 3D Course in Kpk,Revit 3D Course in peshwar,Revit 3D Course in mansehra,Revit 3D Course in lahore,Revit 3D Course in karachi,Revit 3D Course in mianwali,Revit 3D Course in gujrat,Revit 3D Course in gujranwala,Revit 3D Course in multan,Revit 3D Course in sahiwal,Revit 3D Course in jhelum,Revit 3D Course in sialkot,Revit 3D Course in Peshawar quetta,
Revit 3D is a Building design and construction software. Revit building design software is specifically built for Building Information Modeling (BIM), including features for architectural design, MEP and structural engineering, and the outset, Revit was intended to allow architects and other building professionals to design and document a building by creating a parametric three-dimensional model that included both the geometry and non-geometric design and construction information, which later became known as Building Information Modeling or BIM. At the time, several other software packages such as ArchiCAD and Reflex allowed working with a three-dimensional virtual building model, and allowed individual components to be controlled by parameters (parametric components). Two key differences in Revit were that its parametric components were created using a graphical "family editor" rather than a programming language, and all relationships between components, views, and annotations were captured by the model so that a change to any element would automatically propagate to keep the model ;
Course Outlines of Revit 3D Course:
1:Introduction to Revit
2:Basic Drawing and Editing
3:etting up Levels and Grids
4:Drawing and Modifying Walls
5:Doors and Windows
6:Curtain Walls
7:Creating Views
8:Floors
9:Components
10:Reflected Ceiling Plans
11:Roofs
12:Vertical Circulation
13:Construction Documentation
14:Annotation
15:Tags and Schedules
16:Detailing in Revit

Course Fee : 20000
Duaration : 2 Months,

Autocad 2D-3D Computer Course Contents:-
1:Introduction to AutoCAD.
2:2D
3:3D
4:Elevation
5:Section
6:Practical Assignments.
7:Composite Solid Models
8:Advanced 3D Concepts
9:Plotting 3D Models
10:3D Functions
Revit 3D Computer Course Contents:-
1:Introduction to Revit
2:Basic Drawing and Editing
3:etting up Levels and Grids
4:Drawing and Modifying Walls
5:Doors and Windows
6:Curtain Walls
7:Creating Views
8:Floors
9:Components
10:Reflected Ceiling Plans
11:Roofs
12:Vertical Circulation
13:Construction Documentation
14:Annotation
15:Tags and Schedules
16:Detailing in Revit

Cost: 20000 PKR

Duration: Upto 2 Months

Generator Repairing - Appxone Training Center , Pakistan, Karachi

Mon, 14 May 2018 15:05:00 +04

Generator Repairing Course

1. Basic Theory of Power Generation
2. Power Generation Method
3. IC and EC Engines
4. Types of Fuels
5. Two Stroke and Four Stroke Cycle Engine

6. BASIC PARTS OF ENGINE DESCRIPTION

i. Piston
ii. Rings
iii. Engine Blocks
iv. Crank Shaft
v. Cam Shaft
vi. Head
vii. Valves
viii. Current Circuit
ix. Fly Wheel

7. Dismantling of Engines
8. Fault Diagnosis
9. Parts Reparining
10. Parts Replacement
11. Complete Assembling of Engine
12. Tools Usage
13. Winding Theory
14. Winding Repairs
15. AVR Description

Cost: 6000 PKR

Duration: 2 Months

Pro Engineer - Appxone Training Center , Karachi

Wed, 01 Nov 2017 15:51:31 +04

Pro-engineer/Creo is broken into five major areas:

Part Modeling and Design

Installation of software

Orientation of software environment

Sketching of 2D

Part modeling

Extrude command practice

Round command practice

Chamfer and rib practice

Shell and revolve practice

Draft and pattern

Sweep practice

Blend/, and helical sweep

Obtaining views from 3D

Dimensioning

Producing manufacturing drawings

Cost: 7000 PKR

Duration: 2 Months

Wireless Communication - Appxone Training Center , Karachi

Wed, 01 Nov 2017 15:47:58 +04

Communication using xbee transceivers.

Communication using low cost RF module

Communication and Monitoring system using GSM (SIM900
module)

Communication and Data entry using Bluetooth (android and pc)

Communication and home appliances control using Wifi

Live video streaming of IP camera using Wifi cloud configuration.

Controlling of Robots and RC cars using RC remotes

Facilities:

- Individual computer system for each student.

- Maximum 12 students per batch to create smart environment.

- Kits will be provided.

- Highly qualified faculty.

- Practical approach

- Online solution of personal projects

Cost: 8000 PKR

Duration: 2 Months

Basic Electronics - Appxone Training Center , Karachi

Wed, 01 Nov 2017 15:42:35 +04

Basic Electronics concepts

Electrical Quantities and Units

Fundamental laws

Resistors and laws of Resistance

Capacitors

Inductors

Filters

Relays

Semiconductor Theory

PN junction diode and application circuits

Transistors Circuits and Amplifier

Operational Amplifier (OPAMP) and Application Circuits

Introduction to Digital Logic Design

Lab Project/, Etc.

Cost: 8000 PKR

Duration: 2 Months

PCB Design - Appxone Training Center , Karachi

Wed, 01 Nov 2017 13:01:46 +04

Introduction to PCB
Basic Terminology.
Multi Layers concept
Complete pcb making process.
Schematic Capture/, ERC & generating Netlist & BoM
Placement and Lay outing of components on PCB
Design Rule Considerations for better PCB manufacturing
DesignSpark PCB Tips and Tricks for professional look.
DesignSpark Calculator tool
PCB Board Generator Wizard
3D view of Designed PCB.
Seven task of PCB making with hands on.

Cost: 7000 PKR

Duration: 2 Months

Robotics / Mechatronics - Appxone Training Center , Karachi

Mon, 23 Oct 2017 13:41:41 +04

Session 1: Getting started with digital world
Session 2: Analog world interface
Session 3: LCD and Serial Port interface with data display
Session 4:Actuators
Session 5: Wireless Links (Short range)
Session 6: Wireless Links (Long range) and GPS
Session 7: Bluetooth controlled and line following ROBOT
Session 8: Wall following and IR controlled ROBOT
Session 9; Controlling and monitoring hardware using GUI
Session 10: Interfacing Processing software with hardware
Session 11: Controlling robot using voice and generating voice using text
Session 12: RFID and fingerprint based security
Session 13: Kinect interface

Cost: 9000 PKR

Duration: 2 Months

PLC - Appxone Training Center , Karachi

Mon, 23 Oct 2017 13:37:02 +04

BASICS OF PLC
PROGRAMMABLE LOGIC CONTROLLER)
PLC HARDWARE INTRODUCTION
I/O CONTROL LADDER PROGRAMMING IN DETAIL
SENSORS INTERFACING
HMI TOUCH PANEL INTRODUCTION AND PROGRAMMING
PLC INTERFACE WITH HMI(HUMMAN MACHINE INTERFACE)
INTRODUCTION TO INTERFACE WITH INDUSTRIAL EQUIPMENTS

ACTIVITIES:
STREET LIGHT CONTROL/, VFD CONTROL/,
PID TEMPERATURE CONTROL/,
MOTOR CONTROL LIKE SERVO/, STEPPER and PWM POWER CONTROL

Cost: 8000 PKR

Duration: 2 Months

FPGA - Appxone Training Center , Karachi

Mon, 23 Oct 2017 13:31:02 +04

Session 1: Introductory Session
Session 2: Xilinx 7 Series FPGA CLB Architecture
Session 3: Digital Logic Design Basics
Session 4: Introduction to RTL design techniques through Verilog
Session 5: Familiarization with verification and simulation tool - ModelSim
Session 6: RT-level cornbinationaI circuit Part-1
Session 7: RT-level cornbinationaI circuit Part-2
Session 8: Regular Sequential Circuit
Session 9; Xilinx ISE Design Suite Hands-on Part-1
Session 10: Xilinx ISE Design Suite Hands-on Part-2
Session 11: Testing and Verification Methodology-Automated Testbenches
Session 12: Introduction to System Verilog for efficient testbench
Session 13: Xilinx Ise Core Generator Tool Hands-On Part-1
Session 14: Xilinx Ise Core Generator Tool Hands-On Part-2
Session 15: Primitive Level programming techniques for efficient designs
Session 16: Hardware Implementation On FPGA kit

Cost: 10000 PKR

Duration: 2 Months

Embedded System - SmartBrains Engineers & Technologist Pvt Ltd , Gujrat

Tue, 08 Aug 2017 15:45:27 +04

COURSE CONTENT

Course 1: C Language & Embedded C

Why C in EmbeddedOverview
ANSI standardCharacteristics
Function of CFunction Overloading
Conditional StatementsScope Resolution Operator
LoopsClasses in C++
FunctionAccess Specifiers
ArraysConstructor, Destructor
StringsStatic Members, Function
Storage ClassesFriend Classes, Friend functions
Structure & UnionsOperator Overloading
Enumerated Data Types
Bit OperationCourse 5: RTOS (Real Time Operating System)
Pointer
Dynamic Memory AllocationIntroduction to RTOS with Architecture
File handling ConceptMonolithic and Micro Kernel
Raw Data HandlingBooting Vx-Works
Low Level ProgrammingTornado Wind River IDE & simulator
Command Line ArrangementsSource debugging (cross-wind)
Compiler in PracticalPerformance monitoring tools
Data StructuresMemory Management
Sorting & Searching TechniquesInter-task Communication
Concepts & Real Time Exposure Semaphores

Course 2: Microcontroller 8051/AVR/PIC/ARDUINO

Introduction Introduction to ARM Family
Overview of Architecture of 8051/AVR/PIC
Low-Level Programming Concept
Middle Level Programming PIN connect block
Concepts GPID Programming
Cross Compiler Timer Programming
Embedded C/C++ Programming A/D Converter
Embedded C/C++ DebuggingUART Programming
Memory Models I2C & SPI Protocol
Library ReferencePIC
#Pragma Directive VIC (Vector Interrupt Controller)
ON Chip Peripherals CAN Conceptualization
Ports: I/P & O/PI2C Enabled EEPROM Conceptualization
Timer & Counter
Interrupts, ADC, PWMCourse 7: Linux & Device Driver Programming
External Interfaces
LEDS, LCD, SWITCHESLinux Architecture
Seven Segment & Multiplexing 7-segment display Kernel Description
Keypad Matrix Terminal Commands
LED Matrix File Management System
AC/DC relays Process Management System
Motor: DC Motor/ Stepper Motor/ Servo Motor VI Editor
Wireless RF Modules GCC Complier
Zig Bee (Programming + Communication)Shell Scripting
PROTOCOLSUse of make File
SPI, I2C, UART, CANCompile & Debugging
Char Driver Conceptualization

Course 3: ROBOTICS ENGINEER

Robotics IntroductionIntroduction to Internet of Things
Chip Level & Component Level ElectronicsIntroduction to Raspberry Pi
Various Motor for Robot DevelopmentTools: Win 32 image write & SD Formatter
Power Supply DesigningWading Raspbrion OS image on SD Card
Robotic Sensor Designing & InterfacingDemo Programming using C
Robotic Motor Controller CircuitBacking up Updating SD card & OS Image
Embedded C ProgrammingInstalling Wiring Pi Package
I/O FunctionsControlling the Raspberry Pi GPIO by Command
PWMNetworking with Pi
ADCClient-Server Programing for Automating Device/Sniffing Device state
Inter Robot CommunicationIOT-Cloud Installing
Practical Electronics & Sensor DevelopmentInstalling & configuring PubNub SDK for C Language
Practical working with Electronic ComponentsCreating credentials with PubNub Cloud Server
Resistor, Capacitor, Diodes, Transistor, RelayEnd to End IOT Programming demonstrations
Designing of Logic gate & Power Supply
Development of Sensor like Light, Surface etc
Sensors
Gyro & Accelerometer, Ultrasonic sensors, RFID, GPS, PIR Sensor, Temperature Sensor
Touch Pad, Gas Sensor, DTMF, RTC, Finger Print Sensor, RS 232, Alcohol Sensor, Humidity Sensor, Sound Sensor, Surface Sensor, Flex Sensor, Buzzer, Relay

Cost: 1200 USD

Duration: Upto 6 Weeks