Laimoon.com

Mechanical Engineering for Rotating Equipements - GBA -Professional London Training Center , Australia, Germany, India, Netherlands, Turkey, UAE, United Kingdom, Dubai, Delhi, Mumbai, Sydney, London, Istanbul, Frankfurt, Munich, The Hague

Tue, 23 Dec 2025 19:50:07 +04

This programme provides a comprehensive understanding of the mechanical engineering principles that underpin the design, operation, and maintenance of rotating equipment used in industrial environments. It focuses on key assets such as pumps, compressors, turbines, motors, and gearboxes that are critical to reliability, safety, and operational efficiency.

Participants will explore the fundamentals of rotating machinery, including bearings, shafts, seals, lubrication systems, vibration, alignment, and balancing. The programme also covers condition monitoring, fault diagnosis, maintenance strategies, and reliability improvement techniques. By the end of the training, participants will be equipped with the practical knowledge needed to operate, maintain, and troubleshoot rotating equipment effectively, reducing downtime and extending asset life.

Cost: 4250 USD

Duration: 5 Days

Gas Turbine Technology - GBA -Professional London Training Center , Australia, Germany, India, Netherlands, Turkey, UAE, United Kingdom, Dubai, Delhi, Mumbai, Sydney, London, Istanbul, Frankfurt, Munich, The Hague

Tue, 23 Dec 2025 19:40:35 +04

Overview

This training programme provides a comprehensive introduction to gas turbine technology, focusing on the principles, design, operation, and performance of gas turbine systems used in power generation, oil and gas, and industrial applications. It equips participants with a clear understanding of how gas turbines convert energy, their key components, and the factors affecting efficiency, reliability, and emissions.

Participants will explore gas turbine thermodynamics, mechanical and control systems, fuel systems, and auxiliary equipment, along with operational practices, maintenance strategies, and troubleshooting techniques. The programme also addresses performance monitoring, safety considerations, and recent technological developments, enabling participants to operate, manage, and maintain gas turbine systems effectively and efficiently.

Objective

Gain a thorough understanding of gas turbine components, energy transformations within gas turbines, and the analysis of gas turbine performance cycles
Identify the impact of fuel choice on corrosion, emissions, and component life
Understand the relationship between ambient temperature and pressure on gas turbine performance
Understand detailed insights into the control systems, power electronics, and electrical components of gas turbines
Develop the skills to conduct market analysis for gas turbines

Cost: 4250 USD

Duration: 5 Days

EV Engineering and System Integration - Learners Point Training Institute , Bahrain, Kuwait, Qatar, Saudi Arabia, UAE, Dubai, Abu Dhabi, Sharjah, Fujairah, Online,Kuwait,Oman,Qatar,Saudi Arabia,United Arab Emirates

Thu, 01 May 2025 16:03:41 +04

EV Engineering and System Integration Certification

Overview:

The EV Engineering and System Integration Certification is a comprehensive training program designed for professionals seeking to build a career in the electric vehicle (EV) industry. This industry-focused course offers hands-on experience with advanced tools like Simulink, Ansys, Python, MATLAB, and Autodesk Fusion 360. Delivered by seasoned instructors with over 10 years of experience in the EV and technology sectors, this course ensures participants gain real-world insights and practical knowledge across diverse EV use cases.

Importance of the Course

Growing Demand in the EV Industry: The electric vehicle sector is expanding rapidly, particularly in regions like UAE and Dubai, creating a strong demand for skilled professionals.
Industry-Relevant Skills: This course equips you with the practical skills and knowledge needed to excel in EV engineering and system integration, ensuring you are well-prepared for the workforce.
Real-World Application: The course offers hands-on experience with industry-standard tools like MATLAB, Simulink, Ansys, and Python, making you job-ready for advanced roles in the EV industry.
Comprehensive Coverage: From EV architecture to powertrain systems, battery management, and thermal strategies, this course covers all crucial aspects of EV technology.
Career-Ready Preparation: The course includes job roles and responsibilities specific to the EV industry, giving you a clear path to success in an expanding market.
Sustainable Future: Gain insights into sustainability and innovations in EV manufacturing and circular economy, making you an asset to companies prioritizing green technologies.

Benefits of Enrolling in the Training Program

Industry-Focused Learning: Gain practical experience working with tools like MATLAB, Simulink, and Ansys, ensuring a deep understanding of EV systems and components.
Hands-On Projects: Develop 5+ real-world industry use cases across diverse EV scenarios.
Expert Instructors: Learn from industry experts with over a decade of experience in the EV and tech sectors.
Job Market Preparedness: Familiarity with job roles and responsibilities in the EV industry, preparing you for immediate career opportunities.
Lifetime Access: Enjoy lifetime access to course materials and future updates, ensuring your skills remain current.

Course Modules

Module 1: Introduction to EV Systems & Architecture

EV vs. Internal Combustion Engine (ICE) Overview
EV Types: BEV, HEV, PHEV, FCEV – Pros & Cons
Vehicle Development Process (Concept → Design → Testing → Deployment)
Systems Integration Overview
Case Study: Tesla vs. Traditional Automakers – EV Design Evolution

Module 2: Hybrid & Electric Powertrain Components

Hybrid Components & Architectures
Major Powertrain Components (Motors, Batteries, Power Electronics)
Controls Integration & Component Sizing Trade-offs
System Design Considerations (Energy, Efficiency, Torque, Thermal)
Software Lab: MATLAB/Simulink – EV Powertrain Simulation

Module 3: Vehicle Integration & Control Systems

Vehicle-Level Integration (Performance, Drivability, NVH)
Chassis & Powertrain Interaction (Braking, Steering, Ride Handling)
HV/LV Electrical Systems – Safety & Charging Architecture
In-Vehicle Displays & Information Systems (User Experience & Efficiency Aids)
Software Lab: CAN Communication & Embedded Control for EVs

Module 4: Verification, Validation & Testing in EV Development

Testing & Validation Processes (Component, System, Fleet Testing)
Regulatory Standards: SAE, UL, IEC, FMVSS
Safety Testing & Certification (Short Circuit, Overcharge, Fire Exposure)
Hands-on Demo: Battery Testing & EV Component Testing

Module 5: Electric Motors & Motor Control

Maxwell’s Equations & Magnetic Circuits
Motor Types: PM Motors, Induction Motors, Switched Reluctance Motors
Torque Production, Non-linear Magnetic Behavior, Losses & Efficiency
Hands-on Lab: Motor Control using MATLAB/Simulink

Module 6: Battery Technology & Management Systems

Lithium-Ion Battery Chemistry, Design & Safety Considerations
Battery Pack Design (Thermal, Electrical, Structural Considerations)
Battery Management Systems (BMS) – Functions, Control, & Estimation
Simulation Lab: Battery Pack Simulation using Simulink & Ansys

Module 7: Power Electronics & Charging Infrastructure

Power Converters: Buck, Boost, Inverter Design & Efficiency
Semiconductor Devices: IGBTs, MOSFETs, SiC/GaN Trends
Charging Infrastructure & Standards: SAE J1772, Inductive & DC Fast Charging
Lab: Converter & Inverter Control Design in MATLAB/Python

Module 8: Embedded Systems & AI in EVs

Embedded Controllers & Communication (CAN, LIN, FlexRay)
AI in EVs: Predictive Maintenance, Battery Health Monitoring
Real-time BMS & Motor Control using AI/ML Models
Hands-on: Implementing AI-Based Battery Management using Python

Module 9: Thermal Management in EVs

Battery & Power Electronics Thermal Considerations
Active vs. Passive Cooling – Air, Liquid, PCM, Heat Pipes
Case Study: Tesla vs. Lucid vs. Rivian – Thermal Strategies
Simulation Lab: Battery Thermal Management in ANSYS

Module 10: EV Manufacturing & Sustainability

Manufacturing Processes: Cell-to-Pack & Cell-to-Chassis Innovations
Sustainability & Second-Life Batteries (Reuse, Recycling, Disposal)
Industry Panel: Experts on EV Manufacturing & Circular Economy

Module 11: System-Level Optimization & Smart Charging

Energy Management Strategies for Extended Range
Vehicle-to-Grid (V2G) & Bi-directional Charging
Hands-on: Developing Smart Charging Algorithms in Python

Module 12: Final Project & Industry Readiness

Capstone Project – Real-World EV Design or Simulation
Resume Building & Career Guidance
Final Presentations & Certification

Testimonials

Mona Al Qassim, Powertrain Integration Engineer

"The training was a game-changer for me. With the practical application of tools such as Ansys and Autodesk Fusion 360, I was able to understand complex EV architectures ;

Khaled Al Mansoori, EV Systems Engineer

“The EV Engineering and System Integration Certification provided me with invaluable knowledge and hands-on experience in electric ;

Cost: 3000 AED

Discount: 50% Off for Laimoon Users!

Duration: 3 Months

PTC Creo - TAYBA Educational Management , UAE, Dubai, Ajman, Online

Tue, 14 Jan 2025 16:35:20 +04

Creo, the shorthand name for Creo Parametric, is a powerful and intuitive 3D CAD software optimized to address the challenges organizations face as they design, analyze, and share information with downstream partners.

Course Outline
1) Introduction to 3D CAD and PTC Creo
2) User Interface and it’s Customization
3) Sketching in Creo (2D & 3D Sketch)
4) Creating Parts in PTC Creo
5) Base Features (Extrude, Revolve, Sweep, Blend, Swept Blend, Boundary Blend)
6) Engineering Features ( Hole, Round, Chamfer, Shell, Rib, Draft)
7) Creating Additional Reference Geometry ( Planes, Point, Axes, Coordinate systems)
8) Transformation features and their applications ( Pattern, Mirror, Copy)
9)Part Visualization ( Cross sections, Custom Views)
10) Applying Material properties and Mass property evaluation
11)Creating Configurations in Creo ( Family Tables)
12) Creating Simplified Representations of Parts
13) Introduction to Advanced Framework Extension and its applications
14)Introduction to Sheet Metal Parts and its applications
15)Assembly Modeling
16) Assembly Mates ( Constraints and Connections)
17) Creating Sub-Assemblies
18) Replacing Components
19) Assembly Features ( Cut, Hole, Weld, etc)
20) Assembly Pattern
21) Assembly Visualization and Data Exchange
22) Assembly evaluation ( Interference detection, Collision detection, etc)
23) Creating Exploded states
24) Assembly BOM (Bills of Material)
25) Detailing in PTC Creo ( Creo Drawings)
26) Basic and Advanced View Creation
27) Annotating with dimensions, notes, symbols, etc
28) Displaying BOM, Weldment Cut list, Flat pattern Views, etc
29) Creating and Editing Drawing Templates
30) Creating and Editing Sheet Formats
31) Introduction to Piping and Cabling Design

Cost: 5000 AED

Duration: Upto 60 Hours

Autodesk fusion 360 - TAYBA Educational Management , UAE, Dubai, Ajman, Online

Tue, 14 Jan 2025 16:05:16 +04

Fusion 360 is a modern 3D CAD/CAM tool for product development. With Fusion 360 you have one integrated tool to take your idea from concept to manufacture. With built-in collaboration you can work with anyone, anywhere and because it’s cloud based you can access your designs anywhere, on any device.
DETAILED CONTENTS
Introduction to Fusion 360.
Details about Fusion 360 Data Panel and Design Interface.
Creating Models.
Sketch and Constrains.
Create a project and invite a collaborator.
Create a design file.
Draw a sketch.
Extrude the sketch.
Add chamfers and fillets.
Assign a material to the model.
Patch Modeling and Editing.
Solid Modeling and Editing.
Parametric Modeling and Editing.
Mesh Modeling.
Free Form Modeling.
Modifying Tools for Modeling.
Creation of Planes.
Assemblies.
Render Settings and Appearance and Scene Setting.
Animations.

Cost: 1300 AED

Duration: Upto 24 Hours

ANSYS - TAYBA Educational Management , Mexico,United Arab Emirates

Tue, 14 Jan 2025 15:47:31 +04

This program will teach you about Traditional ANSYS Graphical User Interface. You will learn to use the simulation for performing static structural finite element analyses and understand modal and thermal ;

Outline:
The complete outline includes the following parts:

Part 1:
FEA & ANSYS
General Analysis Procedure
Creating the Finite Element Model
Running the Solution
Thermal Analysis
ANSYS Basics
Creating the Solid Model
Defining Material Properties
Structural Analysis
Short Topics

Part 2:
Array Parameters
Working with Elements
Coupled Field Analysis
Modal Analysis
Introduction to Nonlinear Analysis
Coupling & Constraint Equations
Beam Modeling
Sub modeling
Bonded Contact
Macro Basics

Cost: 2200 AED

Duration: Upto 60 Hours

SolidWorks - Advanced - TAYBA Educational Management , UAE, Dubai, Ajman, Online

Tue, 14 Jan 2025 15:15:25 +04

Develop proficiency in Solid Works, a powerful 3D CAD software for product design and engineering. This course covers the creation of detailed 3D models, assemblies, and simulations, providing students with the tools to bring innovative product designs to life and optimize them for manufacturing.
3D Modeling: Learn to create detailed 3D models using parametric design principles. Develop skills in part modeling, assembly creation, and surface modeling.
Simulation: Perform simulations to test the functionality and performance of your designs under various conditions. Analyze stress, thermal, and fluid dynamics to optimize product performance.
Drawing Creation: Generate precise 2D drawings and technical documentation from your 3D models, ensuring clear communication of design intent.
Design Optimization: Utilize advanced features such as design automation, configuration management, and sheet metal design to enhance productivity and innovation.

Cost: 2000 AED

Duration: Upto 50 Hours

Diploma in 3Dsmax Interior& exterior Visualization - TAYBA EDUCATIONAL MANAGEMENT , Ajman

Fri, 06 Dec 2024 14:47:36 +04

3Ds Max Design software is a comprehensive rendering, modeling, animation, and editing solution for architects, designers, and planners. Over 999 companies are already using 3Ds Max for 3D rendering around the world in 2021. In the 3D-rendering market, 3Ds Max has a market share of and is expected to grow as more industries continue to implement it, creating numerous employment opportunities for talented 3D ;

Salary Trends: As per a number of career websites, 3D modelers are in high demand in the fields of medicine, architecture, chemistry, engineering, and geology to create models for research and development purposes. The 3D modeling and rendering skill set has, therefore, been highly coveted and well-compensated. In the UAE, the average salary of a 3D Designer is AED 18,900 per month.

Demand and Opportunities: Since 3D modeling is a highly specialized field, there is a high demand for 3D modelers across all industries. As of 2018, the Bureau of Labor Statistics (BLS) reported that employment in the field of 3D modeling had grown by 8-14%, depending on the specialization. A growing number of businesses have begun employing Autodesk 3Ds Max tools, expanding the demand for trained 3D modelers.

Cost: 2500 AED

Duration: Upto 40 Hours

Primavera - TAYBA EDUCATIONAL MANAGEMENT , Ajman

Thu, 05 Dec 2024 11:12:24 +04

Primavera P6 software is a project management tool used to schedule, track, and manage projects. Enrolling for the Primavera P6 course in Sharjah at Rolla Academy is a great way to improve your project management skills and knowledge. Its main function is to help project managers plan and control projects by providing a visual representation of the project timeline. This application is used by thousands of organizations around the world, including many Fortune 500 companies.
After completion of the Primavera P6 course, you will be able to manage all sorts of projects from small ones to large scale.

Cost: 1500 AED

Duration: 25 To 36 Hours

SolidWorks - Advanced - Learnovate Training Center , UAE, Dubai,United Arab Emirates

Thu, 17 Oct 2024 15:07:04 +04

Course Outline

Firstly, Intro to SOLIDWORKS 2016
View and Short keys
Also, Know the Plans
General Settings
In addition, Learn Sketch Tool
Edit and Modify Sketches
Adding Relations and Dimensions
Advanced Dimensioning Techniques
Basic Model Tools (Extrude, Revolve, Sweep, etc.)
Also, Learn about Modify Tools (Fillet, Chamfer, Hole, Wrap Etc.)
Part modeling
Object and Blocks
Sheet Metal Design
Sheet Metal Modification
Moreover, Weldment
Structural Simulation and Reports
Surface Modeling
Surface Editing Tools
Flow Simulation
Working with Project
Assembly of Models
Also, Assembly Tools
Advance Assembly Tools
Motion Study
Generating Drawing Views
Annotation of Drawing Views
Lastly, Sheet Setting and Template.

Cost: 2500 AED

Discount: 20% Off for Laimoon Users!

Duration: 30 To 40 Hours

Primavera P6 - Learnovate Training Center , UAE, Dubai,United Arab Emirates

Thu, 17 Oct 2024 14:54:14 +04

Course Outline

Firstly, Know about the Project Life Cycle
Secondly, How to handle Projects and manage them
After that, Learn Primavera
Creating Project
Also, Creating Project Structure
In addition, Creating a Work Breakdown Structure
Adding Activities
Creating WBS or Activities
Moreover, Create EPS (Multiple Projects)
Know Relationship
Create Relationship
Also, Create Calendars
Assign Constraints
Creating Relation in Primavera
Create Calendars
Scheduling
Role and Resources
Formatting Project Data
Schedule Project
Create Resources
How to Define Cost
Add Baseline of Project
Define Expenses
Project Progress in Tool
Create Baseline and Expenses
Define Cost and Analysis of Cost
How to Define Risk
How to Define Issues
Admin Settings
Generate Reports
Analysis of Reports
Printing and Publishing
Import and Export DATA

Cost: 1400 AED

Discount: 30% Off for Laimoon Users!

Duration: 30 To 40 Hours

VFD (Variable Frequency Drive) and Motors - Easy Learn Training Institute , United Arab Emirates, Dubai, Sharjah

Thu, 18 Jul 2024 15:24:35 +04

The Variable Frequency Drive (VFD) and Motors course provides an in-depth understanding of the principles and applications of electric motors and VFDs in industrial settings. Participants will explore various types of motors, the fundamentals of VFDs, and their advantages in energy efficiency and process control. The course covers essential electrical theories, VFD components, motor control methods, and installation practices. Emphasis is placed on commissioning, troubleshooting, maintenance, and regulatory compliance. Through case studies and practical examples, learners will gain hands-on experience in optimizing motor performance and achieving cost savings. This course is ideal for professionals seeking to enhance their skills in motor and drive technologies and ensure compliance with industry standards.

Course Content:

Introduction to Motors and Drives
- Types of Electric Motors: AC Induction, Synchronous, DC Motors
- Basics of Motor Operation and Applications in Industrial Settings
Fundamentals of Variable Frequency Drives (VFDs)
- Definition and Purpose of VFDs in Motor Control
- Advantages of VFDs in Energy Efficiency and Process Control
Electrical Theory and Principles
- Understanding Voltage, Current, Frequency, and Their Relationship in AC Circuits
- Power Factor Correction and Harmonic Mitigation with VFDs
VFD Components and Configuration
- Detailed Study of VFD Components: Rectifiers, DC Bus, Inverters, Filters
- Programming Interfaces and Parameter Settings for Various Applications
Motor Control Methods
- Open-Loop vs. Closed-Loop Control Systems
- PID Control and Speed Regulation Techniques with VFDs
Installation and Wiring Practices
- Safety Protocols During VFD Installation and Commissioning
- Proper Grounding, Cable Sizing, and Protection Against Electromagnetic Interference (EMI)
Commissioning and Troubleshooting
- Steps for VFD Startup, Initial Setup, and Calibration
- Common VFD Faults, Troubleshooting Techniques, and Diagnostic Tools
Maintenance and Reliability
- Preventive Maintenance Practices for VFDs and Motors
- Importance of Regular Inspections, Lubrication, and Temperature Monitoring
Application Specifics
- VFD Applications in HVAC, Pumps, Fans, Conveyors, and Other Industrial Machinery
- Case Studies and Practical Examples of Successful VFD Installations
Energy Efficiency and Cost Savings
- Techniques for Optimizing Energy Consumption Using VFDs
- Return on Investment (ROI) Calculations and Financial Benefits of VFD Installations
Regulatory Compliance and Standards
- Understanding Industry Standards (IEEE, IEC) for VFDs and Motor Installations
- Compliance with Safety Regulations and Local Codes

Cost: 1500 AED

Duration: Upto 20 Hours

Control panel designing - Easy Learn Training Institute , United Arab Emirates, Dubai, Sharjah

Thu, 18 Jul 2024 15:17:19 +04

The Control Panel Design course offers a comprehensive introduction to the principles and practices of control panel engineering. Participants will explore the fundamental aspects of control panels, including their types, components, and functions. The course covers essential skills such as interpreting circuit diagrams, assembling and wiring panels, and designing layouts using CAD software. Emphasis is placed on testing, commissioning, and troubleshooting to ensure panel functionality and reliability. Safety practices, compliance with industry standards, and integration with systems like SCADA and HMI are key components of the curriculum. The course also includes practical projects and case studies to provide real-world experience and enhance professional development in the field of control panel design.

Course Content:

Introduction to Control Panels
- Definition and Importance in Industrial Processes
- Types of Control Panels (PLC-Based, Relay-Based, etc.)
Components and Their Functions
- Detailed Study of Components: Relays, Contactors, Timers, PLCs, Indicators, etc.
- Understanding the Role and Selection Criteria for Each Component
Circuit Diagrams and Schematics
- Interpretation of Electrical Drawings and Symbols
- Practice in Creating and Modifying Circuit Diagrams
Assembly and Wiring Techniques
- Hands-On Assembly of Control Panels Using Actual Components
- Techniques for Neat and Efficient Wiring, Including Cable Management
Panel Layout and Design
- Factors Influencing Panel Layout: Ergonomics, Accessibility, Safety
- Using CAD Software for Designing and Documenting Panel Layouts
Testing and Commissioning
- Procedures for Functional Testing of Control Panels
- Simulation of Typical Industrial Scenarios to Validate Panel Functionality
Troubleshooting and Maintenance
- Identifying Common Faults and Troubleshooting Techniques
- Importance of Preventive Maintenance and Regular Inspections
Safety Practices and Regulations
- Overview of Safety Standards (NFPA 79, IEC 60204)
- Implementing Safety Protocols During Panel Assembly and Testing
Integration and Interface
- Integration of Control Panels with Other Systems (SCADA, HMI)
- Interface Design Considerations for Operator Interaction
Documentation and Compliance
- Documentation Requirements: Drawings, Manuals, Test Reports
- Compliance with Industry Standards and Regulatory Requirements
Case Studies and Practical Projects
- Real-World Applications and Case Studies of Control Panel Design
- Completion of Practical Projects to Reinforce Learning Outcomes
Professional Development
- Career Pathways and Further Education Opportunities in Control Panel Design
- Networking and Industry Engagement for Ongoing Learning and Skill Development

Cost: 1500 AED

Duration: Upto 20 Hours

HMI designing - Easy Learn Training Institute , United Arab Emirates, Dubai, Sharjah

Thu, 18 Jul 2024 15:00:27 +04

The HMI (Human Machine Interface) course provides a comprehensive overview of the role and importance of HMIs in industrial automation and control systems. Participants will gain insights into designing user-friendly and effective HMI interfaces, utilizing popular software and design tools, and configuring communication protocols for seamless integration with PLCs and other control devices. The course emphasizes best practices in HMI security, navigation, and user experience, and includes hands-on project development and analysis of real-world case studies. Ideal for professionals seeking to enhance their skills in HMI design and implementation, this course equips learners with the knowledge to create intuitive and efficient interfaces for industrial applications.

Course Content:

Introduction to Human Machine Interface (HMI)
- Understanding the Role of HMIs in Industrial Automation and Control Systems
- Exploring the Benefits of Intuitive and User-Friendly HMI Design
- Analyzing Real-World Applications of HMIs in Various Industries
HMI Software and Design Tools
- Familiarizing with Popular HMI Software Platforms and Their Features
- Creating Dynamic and Interactive HMI Screens for Process Visualization
- Implementing Graphical Elements, Animations, and Data Displays
HMI Configuration and Communication
- Configuring Communication Protocols for Seamless Interaction with PLCs and Other Control Devices
- Establishing Data Exchange Between the HMI and Industrial Equipment
- Troubleshooting Communication Issues and Ensuring Reliable Data Transfer
Navigation and User Experience
- Designing Intuitive Navigation Flows
- Enhancing User Experience through Effective HMI Design
- Conducting Usability Testing and Feedback Integration
HMI Security and Best Practices
- Implementing Security Measures to Protect HMI Systems
- Best Practices for Securing HMI Interfaces and Data
- Addressing Common Security Vulnerabilities
HMI Project Development and Case Studies
- Managing HMI Project Lifecycle from Concept to Deployment
- Analyzing Case Studies of Successful HMI Implementations
- Learning from Real-World Challenges and Solutions

Cost: 1500 AED

Duration: Upto 20 Hours

Revit Structure - Learnovate Training Center , UAE, Dubai,Dubai,United Arab Emirates

Thu, 25 Mar 2021 12:16:17 +04

You will be familiar with the ideas and benefits of BIM.
You will understand the fundamental concepts and features of Autodesk Revit MEP.
You will understand how to utilize the parametric 3D design tools to commence project designing.
You will use the automated tools for documentation of the project.
You will develop a primary stage of simplicity and self-confidence with Autodesk Revit MEP with hands-on experience.

Cost: 1500 AED

Discount: 20% Off for Laimoon Users!

Duration: 30 To 40 Hours

Solar Panel Installation - Learnovate Training Center , Dubai,United Arab Emirates

Tue, 23 Mar 2021 13:31:15 +04

Key contents of the course:
Solar PV Design Introduction
Basic Design and Load Calculation
System Sizing (Solar Panel, Charge Controller, Inverter, Batteries, Fuses, Breakers, etc.)
Wiring Diagram and Demonstration (Power and Control Circuit for AC/DC) – Parallel and Series Connection
Support Structure and Framing
Installation Demonstration
Practical Installation Session
Automatic Transfer Switch Connection (Solar, Grid, and Load)
Invertor Installation customized classes.
Onsite corporate training Facility available. Weekdays and Weekends classes.

Cost: 2500 AED

Discount: 15% Off for Laimoon Users!

Duration: Upto 24 Hours

AUTODESK Revit Architecture - Castle Training , UAE, Dubai, Abu Dhabi, Ras al Khaimah, Al Ain, Sharjah, Fujairah, Ajman,Dubai,Abu Dhabi

Wed, 12 Aug 2020 16:26:45 +04

In this course you will learn

Introduction to Autodesk Revit Architecture
Basic Drawing and Editing
Setting-up Levels and Grids
Drawing and Modifying Walls
Doors and Windows
Curtain Walls
Creating Views
Floors
And more, for further details please submit your details and our course representatve will get in touch with you.

Cost: 350 USD

Discount: 20% off until 10th November!

Duration: Upto 1 Month

Level I Machine Lubricant Analyst - LEORON Professional Development Institute , Saudi Arabia, UAE, Dubai, Abu Dhabi, Riyadh, Jeddah, Muscat,Dubai,Muscat,Azerbaijan,Georgia,Kazakhstan,Oman,United Arab Emirates

Tue, 25 Feb 2020 15:14:42 +04

The course provides guidance and competency development to take the Machinery Lubrication Analyst - MLA ISO 18436-4 Exam offered through the International Council for Machinery Lubrication (ICML).
Preparation in the following areas:

I. Maintenance Strategies
II. Lubrication Theory/Fundamentals
III. Lubricant Selection
IV. Lubricant Application
V. Lube Storage and Management
VI. Lube Condition Control
VII. Oil Sampling
VIII. Lubricant Health Monitoring

Cost: 5670 USD

Duration: 5 Days

Certified Draughtsman - Oscar Education Group , UAE, Dubai, Bur Dubai, Deira, Al Qusais,Dubai,United Arab Emirates

Tue, 09 Apr 2019 16:11:31 +04

Nearly all drafting programs lean heavily on the development of math and computer-aided drawing (CAD) skills and Revit . Students participate in both lecture-intensive classes and hands-on learning sessions. Program fields may include electrical/electronic drafting, architectural drafting, and mechanical drafting, as well as drafting and design technology.
This Qualification will teach the student how to operate various CAD software applications and focuses on architectural draughting (drawing of building plans). It will skill the learner to draught via CAD software, the technical drawings of building structures and the complete presentation and construction drawings for submission to the local ;
Revit can be used as a very powerful collaboration tool between different disciplines in the building design sphere. The different disciplines that use Revit approach the program from unique perspectives.
Autodesk Revit Architecture is a robust architectural design and documentationsoftware application created by Autodesk for architects and building professionals. The tools and features that make up Revit Architecture are specifically designed to support building information modeling (BIM) workflows

Cost: 1200 AED

Discount: 50% Off for Laimoon Users!

Duration: 26 To 120 Hours

Autodesk Revit MEP 2019 (BIM) - Edoxi Training Institute , United Arab Emirates, Dubai, Abu Dhabi,Dubai,Abu Dhabi

Tue, 06 Nov 2018 18:11:29 +04

Edoxi Training Institute is the Leading Institute for BIM-Revit Training in UAE. We have branches in Dubai & Abu Dhabi. Autodesk Revit MEP 2019 Course from Edoxi Institute is a complete package of all the various tools you may require in your profession. Get the best Revit Training from us.

We are providing training for Revit Architecture ,Structure and MEP at advanced level. Edoxi Training Institute Dubai is an extended operation of Time Training Centre, which has 24 years of excellence in education field in Abu Dhabi with thousands of professional certified students. Time Training Center is an authorised Autodesk Training Center.

Why Our Revit Courses?

Students gain practical knowledge of the Revit 2019 software by working on real projects and creating excellent building documents and 3D versions for client presentations utilizing the new features contained in the 2019 version of Autodesk REVIT software. Get training on real project. Get training by a professional corporate trainer.

Edoxi / Time Training Institute; Features:
AutoDesk Certified Instructors
One PC for each student with Individual attention by trainer
UAE Ministry of Education Accredited Institute
KHDA Approved Certificate
Flexible Timing (Daily Classes / Evening Batches / Friday Batches)
Revit MEP, Architecture & Strcture Courses available

Cost: 2500 AED

Duration: 45 Hours

AutoCAD 2026( 2D & 3D ) - Elegant Training Center , United Arab Emirates, Dubai,Dubai

Sun, 22 Apr 2018 17:53:36 +04

Our AutoCAD 2026 Advanced Course for AEC is designed for Architects, Engineers, and Construction Professionals who wish to enhance their skills and proficiency in AutoCAD for architectural, structural, and civil engineering projects. This 30-hour course focuses on advanced features of AutoCAD to help professionals create high-quality designs, improve productivity, and streamline the workflow for AEC projects. Gain hands-on experience in creating detailed drawings, 3D modeling, advanced annotations, and documentation, all tailored to the AEC industry's specific needs.
Course Highlights:
Advanced Drawing & Editing Techniques
Dynamic Blocks – Create and manage dynamic blocks to design flexible and reusable elements in architectural and engineering drawings.
Xrefs & Attachments – Learn how to work with external references (Xrefs) for efficient drawing management and collaboration across different teams.
Advanced Layer Management – Master complex layer management techniques for better organization of large AEC projects, including managing layer filters and states.
Object Snapping & Object Tracking – Advanced techniques for precise drawing, aligning, and modeling using object snaps and object tracking.
Complex Polylines & Regions – Learn to work with advanced polylines and regions for creating intricate, accurate shapes required in AEC designs.
Advanced 3D Modeling & Visualization
3D Solids & Surface Modeling – Explore advanced 3D solid modeling and surface modeling techniques to design complex building structures and components.
3D Meshes & Editing – Learn how to manipulate meshes and use 3D editing tools for designing and refining structural elements.
3D Viewing & Navigation – Master the 3D viewing tools, including camera setup, visual styles, and viewport navigation to better present your models.
Modeling Architectural Components – Design advanced architectural elements, such as walls, windows, doors, and roofs, using AutoCAD’s powerful 3D tools.
Rendering & Visualization – Use AutoCAD's rendering tools to create photorealistic views of your 3D models, including lighting, materials, and textures.
Detailed Documentation & Annotations
Multileader & Annotative Scaling – Use multileader and annotative scaling to streamline the annotation process for multi-view drawings.
Sheet Sets & Templates – Organize your project using sheet sets and drawing templates, ensuring consistency and efficiency across all drawings.
Advanced Hatching & Gradients – Master advanced techniques in hatching, gradient fills, and patterns to represent different materials and finishes accurately.
Custom Hatch Patterns & Gradient Fills – Create and apply custom hatch patterns and gradient fills for accurate representation of materials in AEC designs.
BOMs (Bill of Materials) – Automatically generate and manage Bill of Materials from your drawings for accurate reporting and documentation.
AEC-Specific Applications
AEC Toolset Mastery – Dive deep into AutoCAD’s AEC Toolset for specialized tools tailored to architectural, engineering, and construction designs.
Construction Details & Layouts – Learn how to create detailed construction drawings, including foundation plans, wall sections, and MEP layouts.
Structural Elements & Reinforcements – Use advanced AutoCAD tools to create structural elements such as beams, columns, and reinforcements required for AEC projects.
Site Plans & Survey Data – Import and manipulate site survey data to create accurate site plans and topographical maps for construction projects.
Construction Documentation & Reports – Generate detailed construction documents and reports to meet the requirements of local regulations and building codes.
Collaboration & Project Management
Collaboration with BIM – Understand how AutoCAD integrates with BIM workflows, sharing data between AutoCAD and Revit for seamless collaboration in large-scale AEC projects.
Project Templates & Standardization – Set up templates and drawing standards to ensure consistency and efficiency across your projects, adhering to AEC industry norms.
Data Extraction & Linking – Learn how to extract data from your drawings to create spreadsheets and material lists, which are linked directly to the drawings for real-time updates.
Cloud Collaboration – Use AutoCAD Cloud to share and collaborate with teams remotely, accessing and working on projects from anywhere.

Cost: 950 AED

Discount: 50% Off for Laimoon Users!

Duration: Upto 30 Hours

Training On Industrial Automation (PLC & SCADA) - Easy Learn Training Institute , United Arab Emirates, Dubai, Sharjah

Sun, 31 May 2015 16:43:35 +04

The "Training on Industrial Automation (PLC & SCADA) and Wonderware's InTouch (SCADA)" course provides comprehensive instruction on PLC and SCADA systems, emphasizing practical skills and theoretical knowledge essential for engineers. Participants will learn to create SCADA applications, manage database tags, develop graphic displays with animation, and troubleshoot applications effectively. The PLC section covers hardware basics, programming techniques, and hands-on exercises in ladder logic, preparing engineers for real-world automation projects. This course is tailored for professionals seeking expertise in industrial automation technologies to enhance their engineering capabilities.

Course Content:

Wonder ware's In Touch (SCADA)
- Creating a new SCADA application
- Creating Database of Tags
- Creating & Editing graphic display with animation.
- Creating Real-time & Historical Trends
- Creating Alarms & Events
- Writing logic through script
- Connectivity with the different hardware
- Connectivity between software (Excel)
- Commissioning the network nodes
- Troubleshooting the application
PLC (Programmable logic controller)
- Introduction to PLC hardware
- Architectural Evolution of PLC
- Role of PLC in Automation
- Introduction to the field devices attached to PLC
- AB PLC fundamental (Block Diagram of PLC)
- Detail information about PLC component
- Power supply
- CPU
- I/O Modules
- Communication Cards
- Various range available in PLC
- Type of inputs & Outputs
- Source sink Concept in PLC
- Concept of Flags
- Scan cycle execution
- Introduction of PLC software
- Addressing Concepts
- Programming instruction arithmetic & logical
- Load / and / or/ out / and Read / write
- Compare / Add / Sub / And / Or - Block
- Leading edge / trailing edge instructions
- Move block application
- Timer Blocks programming
- Counter block programming
- Advance Instruction
- File handling
- Comment functions
- Master control/set/reset function
- Upload, Download, Monitoring programming
- Standard Procedure to be followed in wringing/writing ladder etc
- Hands on experience on writing programs
- Creating / Editing a ladder logic
- Monitoring / Modifying data table values
- Forcing I/P & O/P
- Troubleshooting and fault diagnostics of PLC
- Documenting the project
- Programming assignments for real-time application
- Communication with SCADA & AB PLC

Cost: 2000 AED

Duration: 20 Hours